SPC or INGELLS
2 posters
Page 1 of 1
SPC or INGELLS
spc or ingalls ball joints?
witch one is better why?
witch one is better why?
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Re: SPC or INGELLS
non. u got bad ball joint? just get the ones they sell at the autopart store cheaper and do the same thing.
EDSEVEN- Elite Member
- posts : 991
Age : 41
Reg date : 2008-03-10
Car Progress
Car completion:
(0/0)
Re: SPC or INGELLS
i need to fix camber
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Re: SPC or INGELLS
for the rear u can us couple of washer and front get a complete upper a arm camber kit. those u listed will fail real fast.
EDSEVEN- Elite Member
- posts : 991
Age : 41
Reg date : 2008-03-10
Car Progress
Car completion:
(0/0)
Re: SPC or INGELLS
the ball joints???
but its too late i already bought them for 140 for 2
i didint know when u make offer and they like u have to buy
but it was a OK deal
but its too late i already bought them for 140 for 2
i didint know when u make offer and they like u have to buy
but it was a OK deal
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Re: SPC or INGELLS
the ball join for camber? i dont think those give you enuf correction.
EDSEVEN- Elite Member
- posts : 991
Age : 41
Reg date : 2008-03-10
Car Progress
Car completion:
(0/0)
Re: SPC or INGELLS
for reals
they say it goes from +1.5 - +3 degrees
they say it goes from +1.5 - +3 degrees
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Re: SPC or INGELLS
install them and see what happen then report back.
EDSEVEN- Elite Member
- posts : 991
Age : 41
Reg date : 2008-03-10
Car Progress
Car completion:
(0/0)
Re: SPC or INGELLS
it comes in tuesday
anyone got a ball joint press i can borrow?
if not where can i get one?
anyone got a ball joint press i can borrow?
if not where can i get one?
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Re: SPC or INGELLS
harbor freight. but u can use a hamer to install it. get the clamp off and usea hammer to knock the old one out the pound the new one in. easy as 1 2 3.
EDSEVEN- Elite Member
- posts : 991
Age : 41
Reg date : 2008-03-10
Car Progress
Car completion:
(0/0)
Re: SPC or INGELLS
what would you hold the arm up with? while u hammer?
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Re: SPC or INGELLS
take it off
EDSEVEN- Elite Member
- posts : 991
Age : 41
Reg date : 2008-03-10
Car Progress
Car completion:
(0/0)
Re: SPC or INGELLS
o i c
just got it now i can put in after X-mas ill get back at u on how good it is
just got it now i can put in after X-mas ill get back at u on how good it is
nastynguyen- 209forums Member
- posts : 94
Age : 32
Reg date : 2009-07-28
Car Progress
Car completion:
(1/100)
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
Wed Jul 17, 2019 2:06 pm by kreativekvs209
» Fender rolling
Sun Sep 17, 2017 11:58 pm by kreativekvs209
» Giving the Acura TL some breathing room
Mon Aug 28, 2017 7:34 pm by TEAMN0KTURNAL
» 89 cressida $500. Jump on it
Tue Aug 22, 2017 12:29 pm by TEAMN0KTURNAL
» 209forums birthday Aug 17th 2005.
Mon Aug 21, 2017 4:48 pm by Admin
» Bringing 209forums.com to 2017
Fri Aug 18, 2017 12:53 pm by Admin
» Wheel repair shop
Tue Mar 27, 2012 10:20 pm by kreativekvs209
» almost done
Wed Mar 07, 2012 10:13 pm by kreativekvs209
» roll out to wekfest
Fri Feb 17, 2012 10:52 am by kreativekvs209
» new from methdesto
Fri Feb 17, 2012 10:49 am by kreativekvs209